[time-nuts] Racal 9420 OCXO
Bob Camp
lists at rtty.us
Thu Aug 25 21:37:56 UTC 2011
Hi
…. and *much* better specified performance than the Racal parts.
Bob
On Aug 25, 2011, at 5:13 PM, Rob Kimberley wrote:
> I seem to remember Racal in the UK buying some Datum (FTS Division) 1000B
> units off me in the 90's.
>
> http://www.n4iqt.com/fts1000b/1000b-r2.pdf
>
> Nice oscillator.
>
> Rob Kimberley
>
> -----Original Message-----
> From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
> Behalf Of Robert Atkinson
> Sent: 25 August 2011 5:24 PM
> To: Discussion of precise time and frequency measurement
> Subject: Re: [time-nuts] Racal 9420 OCXO
>
> I'm pretty sure Racal made these. They are of consistent design over
> different models and many years and are unlike any other manufacturers OXCO
> I've seen. Racal were old school and did prettymuch everything themselves.
> The did do what appears to be a licence built Sulzer though. The MA-259, see
> http://www.radiomuseum.org/r/racal_precision_frequency_stan.html
>
> Regards,
> Robert G8RPI.
>
>
> --- On Thu, 25/8/11, Bob Camp <lists at rtty.us> wrote:
>
> From: Bob Camp <lists at rtty.us>
> Subject: Re: [time-nuts] Racal 9420 OCXO
> To: "'Discussion of precise time and frequency measurement'"
> <time-nuts at febo.com>
> Date: Thursday, 25 August, 2011, 17:01
>
> Hi
>
> Do we know for sure that Racal actually made these OCXO's in house?
>
> My *guess* is that they were made by various companies over the years and
> sold to Racal. The "return for service" would have been a return to Racal
> and then they forward it to the people who made it...
>
> Bob
>
> -----Original Message-----
> From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
> Behalf Of paul swed
> Sent: Wednesday, August 24, 2011 5:10 PM
> To: Discussion of precise time and frequency measurement
> Subject: Re: [time-nuts] Racal 9420 OCXO
>
> Kind of amazing what time-nuts have in there secret documentation.
> Though I do not need this thanks for sharing.
> Regards
> Paul
> WB8TSL
>
> On Wed, Aug 24, 2011 at 4:05 PM, Robert Atkinson
> <robert8rpi at yahoo.co.uk>wrote:
>
>> Hi,
>> I've attached a copy of the catalogue specification for Racals OCXOs.
>> They do have electronic trim as standard. They are used in the 9478
>> frequency standard. The 9478 service manual specfically states that no
>> information
> on
>> the OCXOs is provided and they must be returned to Racal or appointed
> agents
>> for repair.
>>
>> Robert G8RPI
>>
>> --- On Wed, 24/8/11, GandalfG8 at aol.com <GandalfG8 at aol.com> wrote:
>>
>> From: GandalfG8 at aol.com <GandalfG8 at aol.com>
>> Subject: Re: [time-nuts] Racal 9420 OCXO
>> To: time-nuts at febo.com
>> Date: Wednesday, 24 August, 2011, 16:03
>>
>> In a message dated 24/08/2011 00:03:19 GMT Daylight Time,
>> danrae at verizon.net writes:
>>
>> I don't think Racal released circuit diagrams of any of their ovens.
>> I have traced out the circuit of the rapid warm up oven found in a
>> lot of receivers, the 9442-12 and have fixed those, there is a ceramic
>> cap that frequently goes wonky. The two 9420s I have fixed were just
>> broken wires; they seem to have used PVC insulated wire which
>> degrades... I haven't done the homework on those yet.
>>
>> The 9420s I have do have an EFC input as well as a stabilised Voltage
>> out to feed it, and in the receivers I have that use it [RA1795] the
>> fine setting is done from that, coarse setting from the top adjustment.
>> -------------------------
>> Hi Dan
>>
>> I've taken a further look at the RA1794 manual and see now that it
>> does confirm a fine tune pot being available when using the 9420.
>> Having opened up this oscillator I find there are connections to
>> every
> pin
>> on the B7G connector so will assume until proven otherwise that it
>> does meet the interface spec shown in the 1794 manual.
>> I suspect the comments I've seen claiming most do not have the EFC
>> option is more a case that in many installations it isn't used, which
>> isn't
> quite
>> the same thing.
>>
>> Thanks again for your comments.
>>
>> regards
>>
>> Nigel
>>
>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
>
>
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
More information about the Time-nuts_lists.febo.com
mailing list