[time-nuts] TADD-2 Mini Sine or Square signal input?
Edgardo Molina
xe1xus at amsat.org
Wed Nov 14 18:03:25 UTC 2012
Thank you John, If I test as you mention I will share the results.
Regards,
Edgardo Molina
Dirección IPTEL
www.iptel.net.mx
T : 55 55 55202444
M : 04455 10045822
Piensa en Bits SA de CV
Información anexa:
CONFIDENCIALIDAD DE INFORMACION
Este mensaje tiene carácter confidencial. Si usted no es el destinarario de este mensaje, le suplicamos se lo notifique al remitente mediante un correo electrónico y que borre el presente mensaje y sus anexos de su computadora sin retener una copia de los mismos. Queda estrictamente prohibido copiar este mensaje o hacer usode el para cualquier propósito o divulgar su en forma parcial o total su contenido. Gracias.
NON-DISCLOSURE OF INFORMATION
This email is strictly confidential and may also be privileged. If you are not the intended recipient please immediately advise the sender by replying to this e-mail and then deleting the message and its attachments from your computer without keeping a copy. It is strictly forbidden to copy it or use it for any purpose or disclose its contents to any third party. Thank you.
On Nov 14, 2012, at 7:18 AM, John Ackermann N8UR <jra at febo.com> wrote:
> I suspect it will work fine; worst case might be that you add a 3dB attenuator, but I doubt you'll need it. I would test, if you can, to see whether the output jitter varies between the full input level and something that's closer to 1-2V p-p.
>
> John
> ----
>
> On 11/13/2012 9:52 PM, Edgardo Molina wrote:
>> Dear John,
>>
>> Your response is welcome. My square signal input is 3.3V and 50% duty cycle. Low end 0.5V, High end 2.7V.
>>
>> Will I be able to make it without the bypass? Or should I start warming the soldering station?
>>
>> Thanks!
>>
>>
>>
>> Edgardo Molina
>> Dirección IPTEL
>>
>> www.iptel.net.mx
>>
>> T : 55 55 55202444
>> M : 04455 10045822
>>
>> Piensa en Bits SA de CV
>>
>>
>>
>> Información anexa:
>>
>>
>>
>>
>> CONFIDENCIALIDAD DE INFORMACION
>>
>> Este mensaje tiene carácter confidencial. Si usted no es el destinarario de este mensaje, le suplicamos se lo notifique al remitente mediante un correo electrónico y que borre el presente mensaje y sus anexos de su computadora sin retener una copia de los mismos. Queda estrictamente prohibido copiar este mensaje o hacer usode el para cualquier propósito o divulgar su en forma parcial o total su contenido. Gracias.
>>
>>
>> NON-DISCLOSURE OF INFORMATION
>>
>> This email is strictly confidential and may also be privileged. If you are not the intended recipient please immediately advise the sender by replying to this e-mail and then deleting the message and its attachments from your computer without keeping a copy. It is strictly forbidden to copy it or use it for any purpose or disclose its contents to any third party. Thank you.
>>
>>
>>
>>
>>
>>
>> On Nov 13, 2012, at 8:21 PM, John Ackermann N8UR <jra at febo.com> wrote:
>>
>>> Hello Edgardo --
>>>
>>> The T2-Mini uses a wide-range input circuit based on one that Wenzel published with some modifications. It works with a square wave input (I've done some limited testing) but I can't verify whether the input amplitude range will extend as far on either the low or the high side.
>>>
>>> If you want to drive with a true TTL signal, you could bypass the input circuit entirely and feed directly into the PIC, though that would require some soldering.
>>>
>>> John
>>>
>>> On Nov 13, 2012, at 6:48 PM, Edgardo Molina <xe1xus at amsat.org> wrote:
>>>
>>>> Dear Group,
>>>>
>>>> Does anybody know is the TAPR TADD-2 Mini works with input signals with square wave geometry? Or Sine wave only?
>>>>
>>>> Thank you.
>>>>
>>>> Regards,
>>>>
>>>>
>>>>
>>>> Edgardo Molina
>>>> Dirección IPTEL
>>>>
>>>> www.iptel.net.mx
>>>>
>>>> T : 55 55 55202444
>>>> M : 04455 10045822
>>>>
>>>> Piensa en Bits SA de CV
>>>>
>>>>
>>>>
>>>> Información anexa:
>>>>
>>>>
>>>>
>>>>
>>>> CONFIDENCIALIDAD DE INFORMACION
>>>>
>>>> Este mensaje tiene carácter confidencial. Si usted no es el destinarario de este mensaje, le suplicamos se lo notifique al remitente mediante un correo electrónico y que borre el presente mensaje y sus anexos de su computadora sin retener una copia de los mismos. Queda estrictamente prohibido copiar este mensaje o hacer usode el para cualquier propósito o divulgar su en forma parcial o total su contenido. Gracias.
>>>>
>>>>
>>>> NON-DISCLOSURE OF INFORMATION
>>>>
>>>> This email is strictly confidential and may also be privileged. If you are not the intended recipient please immediately advise the sender by replying to this e-mail and then deleting the message and its attachments from your computer without keeping a copy. It is strictly forbidden to copy it or use it for any purpose or disclose its contents to any third party. Thank you.
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> time-nuts mailing list -- time-nuts at febo.com
>>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>>> and follow the instructions there.
>>>
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>>
>
More information about the Time-nuts_lists.febo.com
mailing list