[time-nuts] Buffering the 1pps output from a Z3801A
Didier Juges
didier at cox.net
Thu Mar 27 00:49:30 UTC 2008
The Thunderbolt's output impedance on the PPS output is much less than 50
ohms, more like 5 ohms.
If you terminate the other end of the cable with a good 50 ohms termination,
you will be OK, even though it would be better to put a ~47 ohms series
resistor right at the TB output before driving the cable. This will reduce
the available amplitude, but will reduce ringing even more.
Check this page:
http://www.ko4bb.com/Test_Equipment/CoaxCableMatching.html
I used the PPS output of the Thunderbolt as a fast rise time pulse generator
for cable matching/reflections experiments.
It will show you what to expect when you use that output to drive a long
cable.
Didier KO4BB
> -----Original Message-----
> From: time-nuts-bounces at febo.com
> [mailto:time-nuts-bounces at febo.com] On Behalf Of Dave Brown
> Sent: Wednesday, March 26, 2008 2:57 PM
> To: Discussion of precise time and frequency measurement
> Subject: Re: [time-nuts] Buffering the 1pps output from a Z3801A
>
> Peter
> All comments so far relate only to the Z3801A. The Trimble
> Thunderbolt has a TTL level 1 pps 10 uSec pulse output on a
> BNC connector intended to be loaded with 50 ohms. AFAIK
> there is no ECL level pps output available from the
> Thunderbolt via its 9 pin serial port connector.
> It's cetainly not mentioned in the Thunderbolt documentation if it is.
>
> DaveB, NZ
>
> ----- Original Message -----
> From: "Peter Vince" <pvince at theiet.org>
> To: <time-nuts at febo.com>
> Sent: Thursday, March 27, 2008 2:29 AM
> Subject: [time-nuts] Buffering the 1pps output from a Z3801A
>
>
> > Bruce, et al,
> >
> > The 1pps output of an HP Z3801A and Trimble Thunderbolt is
> > only available (as far as I know) as a balanced ECL signal on the
> > 25-pin connector, with dire warnings in the manuals about not
> > earthing either side of the ECL signals. Would you be able to
> > advise
> > on a simple buffer circuit that would allow me to drive the usual
> > unbalanced 50-ohm coax please?
> >
> > Thanks,
> >
> > Peter Vince (London, England)
> >
> > _______________________________________________
> > time-nuts mailing list -- time-nuts at febo.com
> > To unsubscribe, go to
> > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > and follow the instructions there.
> >
> >
> > --
> > No virus found in this incoming message.
> > Checked by AVG.
> > Version: 7.5.519 / Virus Database: 269.22.0/1342 - Release Date:
> > 25/03/2008 10:26
> >
> >
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
> No virus found in this incoming message.
> Checked by AVG.
> Version: 7.5.519 / Virus Database: 269.21.8/1339 - Release
> Date: 3/22/2008 4:43 PM
>
>
No virus found in this outgoing message.
Checked by AVG.
Version: 7.5.519 / Virus Database: 269.21.8/1339 - Release Date: 3/22/2008
4:43 PM
More information about the Time-nuts_lists.febo.com
mailing list