[time-nuts] Tbolt monitor software

VK3FGJM VK3FGJM at commtelns.com
Thu Jan 22 05:06:14 EST 2009


Hi Ed,

Initially I felt that was the case, but after some brief RS-232
measurement and the ability to see the TX/RX LED radio buttons sync with
TX and RX data on the serial activity Monitor at the bottom left corner,
there is nothing wrong with the RS-232 lines.

Does anyone have a later version of the Trimble Thunderbolt monitor
program or any other thoughts?


Kind regards,

Gerald

VK3FGJM


-----Original Message-----
From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
Behalf Of Ed, k1ggi
Sent: Thursday, 22 January 2009 1:24 PM
To: 'Discussion of precise time and frequency measurement'
Subject: Re: [time-nuts] Tbolt monitor software

Sounds like the tbolt is not getting the queries from the pc and
therefore the responses are absent, but the pc is getting the
unsolicited info from the tbolt. A fault with pin 3 on the DE9 would do
it, or something deeper that kills the pc-to-tbolt comms.
Ed, k1ggi

-----Original Message-----
From: VK3FGJM [mailto:VK3FGJM at commtelns.com]
Sent: Wednesday, January 21, 2009 3:32 PM
To: time-nuts at febo.com
Subject: Re: [time-nuts] Tbolt monitor software

Hi,

Yes, I can see alarm status and changes when unplugging antenna etc.

As mentioned the unit actually works, just no data certain displayed.

Regards,

Gerald
VK3FGJM



-----Original Message-----
From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
Behalf Of n3izn at aol.com
Sent: Thursday, 22 January 2009 3:55 AM
To: time-nuts at febo.com
Subject: Re: [time-nuts] Tbolt monitor software

Did you select the right comm port? I power mine off a lot and it has
always come back.


-----Original Message-----
From: VK3FGJM <VK3FGJM at commtelns.com>
To: time-nuts at febo.com
Sent: Wed, 21 Jan 2009 5:29 am
Subject: [time-nuts] Tbolt monitor software



Hi group,
 
A strange situation has led me to ask a question about the Tbolt GPSDO
and the Trimble Thunderbolt monitor s/w version 2.6.
 
While re-arrangement of the shack, it's been idle for 3 weeks, Tbolt
turned off. After turning the unit on and letting it settle some 2 hour,
I connected the monitor program and found the following that I can not
explain and correct:-

*   All SV and AMU have question marks
*   Product info has questions marks
*   the ability to see tracking status is blank.

When last used, some 2 months ago to show a friend, the relevant display
data came up, no issues. Further more, position, critical and minor
alarms are green, disciplining status section such as DAC voltage DAC
value mode and even it's 10MHz out etc etc is fine compared to my trusty
Rubidium standard.
 
Has any one seen this before and is there a setting that may have
inhibited this feature?
 
I have a screen shot, however it may be to large to attach, so let me
know if this will help, I will be glad to forward it to some one with
much more knowledge.
 
Thank you in advance.
 
Regards,
 
 
Gerald
 
VK3FGJM
 
 
 
 
 
 
 

 

_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.

_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
--
Message  protected by MailGuard: e-mail anti-virus, anti-spam and
content filtering.
http://www.mailguard.com.au/mg



_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.



_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.




More information about the time-nuts mailing list