[time-nuts] HP10811 losing EFC
Bob Camp
lists at cq.nu
Sat Jan 16 04:12:59 UTC 2010
Hi
Diodes rarely fail half way. Either a bond wire goes out or they melt down. If the varicap looks like a diode at DC it should be ok at RF. I would look elsewhere for the problem.
Bob
On Jan 15, 2010, at 11:07 PM, Neville Michie wrote:
> Hi, thanks for the constructive comments.
>
> I took both units out of their cases and gave them a visual inspection.
> I tested the varicap diode as a diode, and checked the values of surrounding resistors.
> When I re-assembled them one of them now works OK. It will take some time to see if it is stable.
> I have an instrument that I can run them in which has an EFC lead that I can easily lift,
> so I am going to apply about 20V through 1megohm to the EFC terminal and see how high the voltage measures,
> that should give me the 6.8 volts regulated plus a diode drop. The diode and the capacitor should stand 20V.
> I dont like trying to run it while dissasembled, that can lead to disasters, but this test should show if
> the 6.8 volts is a problem. Failing that I will unsolder the varicap
> and measure its capacitance on a bridge with changing bias voltage.
> Thanks again for the suggestions,
>
> Neville Michie
>
>
> On 16/01/2010, at 11:54 AM, Rick Karlquist wrote:
>
>> No one has mentioned the fact that the cathode of the varactor
>> is connected to an internal 6.8V Zener diode voltage reference.
>> This is another source of trouble.
>>
>> Rick Karlquist
>> N6RK
>>
>>
>> Bob Camp wrote:
>>> Hi
>>>
>>> I sure would do some quick continuity checks on the EFC line before I
>>> started swapping varicaps out. A bum solder joint opening up is a lot more
>>> likely than the varicap going nuts in a fashion that still lets the
>>> oscillator run.
>>>
>>> Bob
>>>
>>>
>>> On Jan 15, 2010, at 7:08 PM, Neville Michie wrote:
>>>
>>>> Hi,
>>>>
>>>> I have two HP10811 oscillators that do not respond to EFC voltage.
>>>> The latest to fail had been quite accurately set against a TBOLT,
>>>> one morning (after being on standby in a HP5328A) it was off frequency
>>>> and would not shift with EFC but would adjust with the coarse adjust.
>>>> I have bought in two Phillips varicap diodes, BBY40 and BB149A,
>>>> but before I did some damage fault finding in the HP10811s I thought
>>>> it wise to ask for any advice that was available.
>>>> While I am playing with them I may try to readjust the temperature
>>>> setting
>>>> of the oven to get on top of the turnover. Can anyone point me to that
>>>> article?
>>>>
>>>> cheers, Neville Michie
>>>>
>>>> _______________________________________________
>>>> time-nuts mailing list -- time-nuts at febo.com
>>>> To unsubscribe, go to
>>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>>> and follow the instructions there.
>>>>
>>>
>>>
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to
>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>>
>>>
>>
>>
>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
More information about the Time-nuts_lists.febo.com
mailing list