[time-nuts] Pic programing for the PICTIC II

Bob Camp lists at rtty.us
Wed Jul 7 09:07:21 EDT 2010


Hi

The closest thing I could find were the side adjust parts. They also have "flat on the board" parts and 3/8" squares. No sign of top adjust 1/4" parts ....

Bob


On Jul 7, 2010, at 1:09 AM, Ed Palmer wrote:

> It looks like there's still a problem with the trimmers.  R17 and R22 are shown as part # 3266P-1-502LF and the photo shows the proper type of trimmer.  The data sheet and the catalog page show that 3266P has the adjustment parallel to the board rather than vertical.  Mouser just used the same picture for all styles of the 3266 line.  There are others that are in stock, but they're larger and I don't know if there's room for them on the board.
> 
> Ed
> 
> Bob Bownes wrote:
>> Changed it to a different part that is available. Difference is RHoS
>> compliance method.
>> 
>> Changed the backordered 2n3906 as well. Shaved $0.02 off the total cost!
>> 
>> Bob
>> 
>> 
>> On Fri, Jul 2, 2010 at 3:17 PM, Bob Camp <lists at rtty.us> wrote:
>>  
>>> Hi
>>> 
>>> It looks like it may be a while before the trim pots come in (12 weeks...).
>>> The 3266X (side adjust rather than top adjust) is in stock. I'm not sure if
>>> the layout is "side adjust" friendly or not.
>>> 
>>> Bob
>>> 
>>> -----Original Message-----
>>> From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
>>> Behalf Of Bob Bownes
>>> Sent: Friday, July 02, 2010 2:54 PM
>>> To: Discussion of precise time and frequency measurement
>>> Subject: Re: [time-nuts] Pic programing for the PICTIC II
>>> 
>>> Folks,
>>> 
>>> I put together a mouser 'project' with all of the parts. This means
>>> you can just go to the mouser site and order all the parts for the
>>> project. No need for anyone to do a group buy of parts, re-pack and
>>> re-distribute them. Here's how to get to it:
>>> 
>>> To access the project, click on the url listed below or copy and paste
>>> it into your web browser:
>>> 
>>> http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c7ada9ced0
>>> 
>>> Or you can access the project by going to http://www.mouser.com/ and
>>> click on the EZ Buy option on the top navigation bar. You can also
>>> click on this link or copy and paste it into your browser:
>>> http://www.mouser.com/Tools/Tools.aspx. Then enter the following
>>> access number listed below into the Project Access ID function.
>>> 
>>> c7ada9ced0
>>> 
>>> 
>>> Total cost w/o shipping is $30.30.
>>> 
>>> 
>>> On Fri, Jul 2, 2010 at 1:23 PM, Peter Vince <pvince at theiet.org> wrote:
>>>    
>>>> Apologies for the previous incomplete message - somehow my laptop
>>>> trackpad jumped the cursor over the send button :-(
>>>> 
>>>>      
>>>>> Better ?
>>>>> How many16f688s are we talking here?
>>>>> 
>>>>> My thinking is less than 10 as only two people have asked.
>>>>> Don't know how many have not asked.
>>>>>        
>>>> I would also like a pre-programmed PIC please, if someone can arrange
>>>> that.  Or ideally, a complete kit of parts, but as the previous
>>>> correspondent has written, I appreciate that is a lot of work.
>>>> 
>>>> Thanks,
>>>> 
>>>>    Peter Vince  (London, England)
>>>> 
>>>> _______________________________________________
>>>> time-nuts mailing list -- time-nuts at febo.com
>>>> To unsubscribe, go to
>>>>      
>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>>    
>>>> and follow the instructions there.
>>>> 
>>>>      
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to
>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>> 
>>> 
>>> 
>>> 
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>> 
>>>    
>> 
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>> 
>>  
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
> 





More information about the time-nuts mailing list