[time-nuts] Austron 2100F

paul swed paulswedb at gmail.com
Fri Oct 22 21:58:00 EDT 2010


Bert always amazing hope you are well.
Regards
Paul.

On Fri, Oct 22, 2010 at 6:02 PM, <EWKehren at aol.com> wrote:

> Send me a picture direct to my email. I may have one.   Bert  Kehren
>
>
> In a message dated 10/22/2010 6:01:13 P.M. Eastern Daylight Time,  as
> magal at fc.up.pt writes:
>
> With an  outboard +/- 12 Volt power source my 2100F is now working fine.
> A new  replacement package is therefore desperately needed.
>
> Best  regards,
> Antonio
> CT1TE
>
> Quoting asmagal at fc.up.pt:
>
> > Dear  All,
> >
> > Diving into the hardware, I found the DC-DC +5 to +/-12 V  Power Source
> > defective. There may be something more but that is  serious enough.
> >
> > Thank you for your kind attention and  help.
> >
> > Antonio
> > CT1TE
> >
> > Quoting paul swed  <paulswedb at gmail.com>:
> >
> >> Thats what I was thinking  also on the reference and emailed back to the
> >> group.
> >> I  believe over time that internal switch to select 1,5,10 mc can get a
> bit
> >> touchy.
> >> If a operating reference is connected and  checked to be correct toggle
> the
> >> switch a few times to clean its  contacts. It gets lonely sitting in
> there by
> >> itself for years.  ;-)
> >> Regards
> >> Paul.
> >>
> >> On Fri, Oct  22, 2010 at 8:12 AM, Chuck Harris <cfharris at erols.com>
> wrote:
> >>
> >>> Hi Antonio,
> >>>
> >>>  Ok.  I just wanted to be sure that it was still up in Europe.   Canada
> >>> dropped their chains 3 months earlier than they said  they would.  And
> >>> since Loran-C is no longer usable world  wide, I figure Europe will be
> >>> dropping their chain  soon.
> >>>
> >>> The error indication you have described  tells me that you have no
> >>> reference oscillator.  This  could be for a couple of reasons:
> >>>
> >>> 1) you have  no frequency standard connected to your 2100F
> >>> 2) the switch,  labeled 1-5-10, on the board stack visible when you
> hinge
> >>>  open the front panel is set incorrectly for your  external frequency
> >>>  standard.
> >>> 3) Your  2100F is broken.
> >>>
> >>> -Chuck  Harris
> >>>
> >>> asmagal at fc.up.pt  wrote:
> >>>
> >>>>  Chuck,
> >>>>
> >>>> I am in Portugal, currently  receiving the European
> >>>> 6731 LESSAY  Chain.
> >>>>
> >>>> Best  regards,
> >>>> Antonio
> >>>>  CT1TE
> >>>>
> >>>> Quoting Chuck Harris  <cfharris at erols.com>:
> >>>>
> >>>> Are you  sure that your Loran chain is still up? In the US and
> >>>>>  Canada, Loran has been  decommissioned.
> >>>>>
> >>>>
> >>>  _______________________________________________
> >>> time-nuts  mailing list -- time-nuts at febo.com
> >>> To unsubscribe, go  to
> >>>  https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> >>> and  follow the instructions there.
> >>>
> >>  _______________________________________________
> >> time-nuts mailing  list -- time-nuts at febo.com
> >> To unsubscribe, go to
> >>  https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> >> and follow  the instructions  there.
> >>
>
>
>
>
> _______________________________________________
> time-nuts  mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the  instructions there.
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>



More information about the time-nuts mailing list