[time-nuts] HP Z3805A com port and monitoring questions

[Said Jackson]

Edgardo,

Pretty sure it was 9600 8N1 no flow control.

Came right up in GPSCon..

Maybe its your cable, I used the cable that was shipped to me with the unit.

I did have to manually initiate the auto survey, so comms are important..

Bye
Said

Sent From iPhone

On Oct 14, 2012, at 21:36, Edgardo Molina <xe1xus at amsat.org> wrote:

> Dear Said,
> 
> I am having a very hard time trying to guess the communication port configuration of the HP Z3805A. I am trying with different port settings to match the PC and using different monitor and control programs. The afternoon was not that fruitful regarding this. Is there a chance you have the default port configuration for the Z3805A so I can match my PC serial port configuration?
> 
> I might be unavailable to respond to you tomorrow during the day, as I will be at Queretaro with restricted access to the Internet. Despite this I will be able to read my mail, not respond to it. Hope you don't mind.
> 
> Your kind help is always welcome. Thanks.
> 
> Regards,
> 
> 
> 
> Edgardo Molina
> Dirección IPTEL
> 
> www.iptel.net.mx
> 
> T : 55 55 55202444
> M : 04455 20501854
> 
> Piensa en Bits SA de CV
> 
> 
> 
> Información anexa:
> 
> 
> 
> 
> CONFIDENCIALIDAD DE INFORMACION
> 
> Este mensaje tiene carácter confidencial. Si usted no es el destinarario de este mensaje, le suplicamos se lo notifique al remitente mediante un correo electrónico y que borre el presente mensaje y sus anexos de su computadora sin retener una copia de los mismos. Queda estrictamente prohibido copiar este mensaje o hacer usode el para cualquier propósito o divulgar su en forma parcial o total su contenido. Gracias.
> 
> 
> NON-DISCLOSURE OF INFORMATION
> 
> This email is strictly confidential and may also be privileged. If you are not the intended recipient please immediately advise the sender by replying to this e-mail and then deleting the message and its attachments from your computer without keeping a copy. It is strictly forbidden to copy it or use it for any purpose or disclose its contents to any third party. Thank you.
> 
> 
> 
> 
> 
> On Oct 14, 2012, at 11:05 PM, SAIDJACK at aol.com wrote:
> 
>> Hi Edgardo,
>> 
>> I think the Z3805A and 58503A are identical, except in the rubber bumpers,  
>> maybe the power supply voltage setting, and the ID string..
>> 
>> I don't really care, the three units I have perform much better than  
>> anything else I have, so that satisfies my requirements..
>> 
>> In fact one of the units' ADEV can only be qualified by the BVA 8600  o
>> scillator I have, and I don't know if I am measuring the BVA performance or the  
>> 58503A because I am measuring right at the specification of the BVA unit.. 
>> Wish  I had two BVA's :)
>> 
>> bye,
>> Said
>> 
>> 
>> In a message dated 10/14/2012 15:41:25 Pacific Daylight Time,  
>> xe1xus at amsat.org writes:
>> 
>> Derived  question: Will I get better GPSDO performance if I use a 58503A 
>> receiver? Or  do you think our units match those 58503A GPSDOs out there?
>> 
>> Again,  thanks to everybody who helped me to figure out about my receivers 
>> and their  inner workings. As always, you all made my day. 
>> 
>> 
>> Best  regards,
>> 
>> 
>> 
>> Edgardo Molina
>> Dirección  IPTEL
>> 
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.