[time-nuts] Fw: FTS 4060 Cesium Time & Frequency Standard, Datum
paul swed
paulswedb at gmail.com
Thu Oct 3 12:56:55 UTC 2013
Tom
I have uploaded rom images to Diddiers and others sites for safe keeping.
Thankfully others do also. Thats exactly how I was able to recover my
HP5100d digital scope. It had alzheimers and though I looked high and low
for an image for 3 years, it was only after I purchased a tek DSO that the
images showed up on Diddiers site. But the fact is they finally did. I
compared the two scopes and the HP remains on the bench. All 60 LBs. The
tek must be 13 LBs its a good scope.
Looks like you have some numbers to start working with. Let us know what
you see.
Regards
Paul.
On Wed, Oct 2, 2013 at 10:53 PM, Tom Miller <tmiller at skylinenet.net> wrote:
>
>
> Just to get this data on the list.
>
> Here are the measured voltages on U1:
>
> Pin Fn Voltage Limits
> 9 Beam I 0.001 1.01 to 3.73
> 18 Ion Pump E 2.436 1.72 to 3.01
> 7 Ion Pump I 0.020 0 to 2.0
> 19 Elec Multi E 2.060 0.84 to 3.01
> 17 C-Field I 3.65 3.28 to 4.45 (front
> panel sw set at 500)
> 16 Cs Oven T 1.379 1.27 to 1.55
> 20 Xtal Oven Pwr 3.57 2.81 to 3.91
> 3 180 MHz Lvl 2.784 0.1 to 4.8
> 2 12.6 MHz Dig 4.84 4.0 to 5.0
> 23 12.6 MHz Ana 1.34 0.35 to 4.28
> 6 +5 Supply 2.427 2.35 to 2.68
> 4 +18 V Supply 2.484 2.42 to 2.68
> 22 - 18 V Supply 2.481 1.72 to 3.52
> 21 Chassis T 3.045 2.62 to 3.44
>
>
> It has been on for four days.
>
> When I compare the 10 MHz out to my GPSDO, the frequency matches up when
> the control (meter 4) passes 3.2 volts. There is no movement in the Beam
> current (meter 3) as control sweeps.
>
>
>
> Tom
>
>
>
> ----- Original Message -----
> From: Tom Knox
> To: Tom Miller ; Time-Nuts
> Sent: Wednesday, October 02, 2013 2:00 PM
> Subject: RE: [time-nuts] FTS 4060 Cesium Time & Frequency Standard, Datum
>
>
>
> If anyone has a service manual I am also very interested. Thanks
> Thomas Knox
>
>
>
> > From: tmiller at skylinenet.net
> > To: time-nuts at febo.com
> > Date: Wed, 2 Oct 2013 13:22:45 -0400
> > Subject: Re: [time-nuts] FTS 4060 Cesium Time & Frequency Standard,
> Datum
> >
> > Hello Corby,
> >
> > Thanks for the help. Yes, could you copy me on the information for the
> U1
> > chip? I do not have anything other than the user manual from Brooke.
> At this
> > time, anything will be a great help.
> >
> >
> > Best regards,
> > Tom
> >
> >
> > ----- Original Message -----
> > From: <cdelect at juno.com>
> > To: <time-nuts at febo.com>
> > Sent: Wednesday, October 02, 2013 11:47 AM
> > Subject: [time-nuts] FTS 4060 Cesium Time & Frequency Standard, Datum
> >
> >
> > Tom,
> >
> > On the 4060 you can easily monitor the Ion pump voltage and current,
> the
> > electron multiplier voltage, and other important parameters by
> measuring
> > the voltages on the U1 chip on the uP board.
> > This saves you fronm having to diconnect stuff to measure the HV and
> > such.
> > If you don't have a manual showing the pins of U1 I can post to pinout
> > here on Time Nuts.
> >
> > Corby
> >
> > _______________________________________________
> > time-nuts mailing list -- time-nuts at febo.com
> > To unsubscribe, go to
> > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > and follow the instructions there.
> >
> > _______________________________________________
> > time-nuts mailing list -- time-nuts at febo.com
> > To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > and follow the instructions there.
>
> =
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
More information about the Time-nuts_lists.febo.com
mailing list