[time-nuts] PRS-45 Cs Standard
Magnus Danielson
magnus at rubidium.dyndns.org
Sat Dec 6 11:46:47 UTC 2014
I sent him the manual so that the serial readout of that digital cesium
becomes easy and trivial.
Cheers,
Magnus
On 12/06/2014 10:56 AM, Bert Kehren via time-nuts wrote:
> Provided the unit works one simple way to get an idea as to the health of
> the tube is to insert a plain multi meter in the 200 mV position. That
> inserts a 10 M resistor in series and you can calculate beam current.
> Bert Kehren
>
>
> In a message dated 12/5/2014 8:38:07 P.M. Eastern Standard Time,
> bob at evoria.net writes:
>
> Hi Magnus,
> I'll certainly do that, but I'm waiting to pull the panels until I know
> that it works. I don't want a finger pointing at me saying I broke it. The
> reason I posed the question was that I'm wondering if this thing, at 11 1/2
> years old, is on it's last dying legs. But, I suppose I won't find that
> out until it's powered up and I can download the status string. What will I
> be looking for? I think I've read something about ion pump current from
> past posts about rehabilitating an old Cs standard. I'll have to go back
> through that thread.
>
> Bob
>
> From: Magnus Danielson <magnus at rubidium.dyndns.org>
> To: time-nuts at febo.com
> Cc: magnus at rubidium.se
> Sent: Friday, December 5, 2014 6:10 PM
> Subject: Re: [time-nuts] PRS-45 Cs Standard
>
> Bob,
>
> Do open up and take a look. Do take photos. Do share. :)
>
> Bet the bottom plate is a good start.
>
> Cheers,
> Magnus
>
> On 12/05/2014 10:31 PM, Bob Stewart wrote:
>> Hi Magnus,
>> It came in today. Looks good from the outside. No obviously bad
> smells, but I can't power it up, as my PSU hasn't come in yet.
>>
>> There is a paper Datum tag dated 6/2/03 on the outside. Looking through
> the vent holes, I can see a Datum Cesium Beam Tube assembly Model Number
> 7613A/077, Part Number 74514-110. I can see that the back two panels have
> been removed and replaced, but nothing obvious has been done on the inside.
> There are two SMB connectors on the main board that don't have anything
> plugged in, but there's nothing obvious that they'd connect to. Does any of
> that tell me something that I don't want to know? It's going to be a long
> wait till Monday. =)
>>
>> Bob
>>
>> From: Magnus Danielson <magnus at rubidium.dyndns.org>
>> To: time-nuts at febo.com
>> Cc: magnus at rubidium.se
>> Sent: Wednesday, December 3, 2014 1:38 PM
>> Subject: Re: [time-nuts] PRS-45 Cs Standard
>>
>> Hi Bob,
>>
>> The manual is in your inbox.
>> It also describes a DS1 interface, which should be interesting to know
>> what the odd telecom signals is about. :)
>>
>> Cheers,
>> Magnus
>>
>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
>
>
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
More information about the Time-nuts_lists.febo.com
mailing list