[time-nuts] FASTRAX GPS
Ernie Peres
ernieperes at aol.com
Wed Jun 11 11:11:41 UTC 2014
Hi Jason,
I figured out a different pin assignments....
hold the PCB so that the SMA antenna connector is looking to right and under the PCB.
open- 1 2- Ant power presently connected to pin nbr 4
TX- 3 4- Main power +3 volt
RX- 5 6- 1PPS
open- 7 8- Grnd power -3 Volt
the unit takes about 60mA @ 3,0 volt and comes-up in NMEA mode.. 9600 Baud.
I use the FASTRAX_WORKBENCH_522 software.
I wonder if anybody has other pin arrangement/connection. The 2 open pins is UNK and also not sure if pin nbr 4 is the main power or perhaps the pin nbr 2......??
Rgds Ernie.
-----Original Message-----
From: time-nuts-request <time-nuts-request at febo.com>
To: time-nuts <time-nuts at febo.com>
Sent: Tue, Jun 10, 2014 6:00 pm
Subject: time-nuts Digest, Vol 119, Issue 18
Send time-nuts mailing list submissions to
time-nuts at febo.com
To subscribe or unsubscribe via the World Wide Web, visit
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
r, via email, send a message with subject or body 'help' to
time-nuts-request at febo.com
You can reach the person managing the list at
time-nuts-owner at febo.com
When replying, please edit your Subject line so it is more specific
han "Re: Contents of time-nuts digest..."
oday's Topics:
1. Re: FASTRAX GPS (Jason Rabel)
2. OT?: Hittite to be bought by AD (John C. Westmoreland, P.E.)
---------------------------------------------------------------------
Message: 1
ate: Mon, 9 Jun 2014 12:10:16 -0500
rom: "Jason Rabel" <jason at extremeoverclocking.com>
o: <time-nuts at febo.com>
ubject: Re: [time-nuts] FASTRAX GPS
essage-ID: <002001cf8405$b0ddc2e0$129948a0$@extremeoverclocking.com>
ontent-Type: text/plain; charset="us-ascii"
Ernie,
I'm having issues right now, I need to find my adapter cable as the one I have
ight now is the wrong pin spacing. I did trace the
ines on the PCB and it appears to be the same as the Resolution-T / Lassen /
ther Trimble pinouts...
Just FYI, I couldn't find a valid link to the 3.41 software since ublox bought
hem and they only have a newer version which I don't
hink supports the old binary protocol, they only support NMEA (supposedly)...
t probably wouldn't hurt to try them out later
hough. I do not know what language the module will start out in...
I did find an older version on the archive.org website, link is below:
https://web.archive.org/web/20070227050436/http://isuite.fastrax.fi/download/gpswb/Setup331.exe
If you dig around on some newer pages there is also a link to a firmware
ownload and the updater software that works.
The pinout for the board *should* be:
1 - Antenna Input (5v - 3V I guess)
- Prime Power - 3.3V
- TXD
- Reserved
- RXD
- 1PPS
- No Connect
- GND
If you hold the module so the SMA is on the LEFT (bottom side), and the pins are
n the far RIGHT facing up.
GND - 8 7 - NC
PS - 6 5 - RX
ES - 4 3 - TX
WR - 2 1 - ANT
For verification, if you look closely you can see the trace going out from Pin-2
's up and down.
------------------------------
Message: 2
ate: Tue, 10 Jun 2014 02:53:20 -0700
rom: "John C. Westmoreland, P.E." <john at westmorelandengineering.com>
o: Discussion of precise time and frequency measurement
<time-nuts at febo.com>
ubject: [time-nuts] OT?: Hittite to be bought by AD
essage-ID:
<CAFtYB4wvL2H1Fs=1uVYNNsFUTvegpZ94v82hZ8yDZYq1g5c9+A at mail.gmail.com>
ontent-Type: text/plain; charset=UTF-8
Hello,
Thought this could be of interest to some of you:
Chipmaker Analog Devices to buy Hittite in $2 billion deal | Reuters
http://uk.reuters.com/article/2014/06/09/uk-analog-devices-acquisition-idUKKBN0EK0Z920140609>
Regards,
ohn W.
-----------------------------
_______________________________________________
ime-nuts mailing list
ime-nuts at febo.com
ttps://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
End of time-nuts Digest, Vol 119, Issue 18
*****************************************
More information about the Time-nuts_lists.febo.com
mailing list