[time-nuts] Lucent KS-24361, HP/Symmetricom Z3809A, Z3810A, Z3811A, Z3812...

[GandalfG8 at aol.com]

Oh, ok, thanks for that, and thanks too for the further information on the  
interface connector.
 
For now though, it's me back to sleep for a while:-)
 
Regards
 
Nigel
GM8PZR
 
 
In a message dated 02/11/2014 14:53:01 GMT Standard Time, kb8tq at n1k.org  
writes:

Hi

Well I for one am not getting at all bored at seeing what  you are doing. I 
find it very encouraging that somebody is sharing all the ins  and outs of 
figuring out what’s going on. Far to often we simply get the end  result and 
not much detail (I for one have been rightly criticized for that  within 
the last day or two …). Keep up the information stream. Keeping the  
information on the list puts it into the archives so it can be dug up by  everybody. 

Bob

> On Nov 2, 2014, at 9:44 AM, GandalfG8---  via time-nuts 
<time-nuts at febo.com> wrote:
> 
> Oh well, and  perhaps not too surprisingly, the J5 pin 3 to ground option 
on 
> its  own was not that much of a raging success.
> 
> However, the unit  did eventually come up indicating "Standby", and at 
that  
> point  pulling out the pin 3 to ground link and inserting the previously 
>  made up  plug switched it into "On" mode and up came the outputs.
>  
> I'm sure everyone is getting a bit tired of hearing me going on   about 
> this, and it's hard to know what else to add other than to say  there 
seems  to 
> be more than one option that will do the trick,  but my wired plug as  
> previously described, and wired according  to the starting in the top 
right hand  
> corner numbering scheme,  does, for me at least, seem to work every time, 
 so I 
> think I'll  just stick with that and quit whilst I'm ahead:-)
> 
>  Regards
> 
> Nigel
> GM8PZR
> 
> 
> In a  message dated 02/11/2014 01:27:18 GMT Standard Time,  
>  golgarfrincham at gmail.com writes:
> 
> Keep in  mind that I  made the modifications to my RFTG-u REF 1 almost
> 4 years ago  and  the details of why I did what I did are kind of foggy
> today. It was  a  pure hack but I *believe* that the circuitry as well
> as the  jumpers were  required, or at least I thought so. The big problem
>  with getting something  like this to work is that after spending a  lot
> of time on it I generally go  on to the next project and as  long as what
> I did works, I forget about it  because it is a one  of a kind thing. The
> photo link below shows the 5Mhz  buffer amp  I connected to the TP in
> front of the oscillator that uses a   mounting bracket that is secured
> by the BNC connector that outputs  the  5Mhz. The 24V/2A power supply that
> I mounted on the back  connects across  the diode on the circuit board as
> shown. The  transistors and other  components of the modification that are
>  mounted free form on the back of  the J5 connector get the +5VDC  from
> the header directly in back of J5. The  wire on the left  goes through an
> existing hole on the circuit board to  connect to  the fault LED.
> 
> I was hoping that someone else would   duplicate the modification just to
> reassure me that what I did wasn't  black  magic. It looks like Nigel is
> doing just   that-thanks.
> 
> 
>  
http://i906.photobucket.com/albums/ac262/rjb1998/RFTG-uREF1_zps546e4c82.jpg
>  _______________________________________________
> time-nuts   mailing list -- time-nuts at febo.com
> To unsubscribe, go to   
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and  follow the  instructions there.
> 
>  _______________________________________________
> time-nuts mailing list  -- time-nuts at febo.com
> To unsubscribe, go to  
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the  instructions there.