[time-nuts] Lucent KS-24361, HP/Symmetricom Z3809A, Z3810A, Z3811A, Z3812...
GandalfG8 at aol.com
GandalfG8 at aol.com
Sun Nov 2 20:32:20 UTC 2014
Given the expected close proximity of these units, presumably it was only
ever intended that they should work as a pair, and I remember Stu Cobb
commenting on how short the supplied link cable is, I wouldn't be too surprised
if there turns out to be no serial comms between the units but perhaps just
handshaking via asserted levels.
Regards
Nigel
GM8PZR
In a message dated 02/11/2014 20:12:35 GMT Standard Time, kb8tq at n1k.org
writes:
Hi
Yes, getting the GPS version worked out is certainly the thing most people
will be after. Doing the other box is a bit further down the road. The
main thing (to me) is documenting the 15 pin connector as best we can. That
way whatever somebody decides to do in the future, they have a good starting
point. Identifying which pins look like RS-422 and which look like CMOS
would go a long way to figuring both sides of this out. When I did the other
connectors, I just ran through them with a DVM. 2.5V = 422 input, 1.5 or 3.5
= 422 output. I didn’t have any CMOS. Everything else was either open
circuit or ground.
Bob
> On Nov 2, 2014, at 3:01 PM, GandalfG8--- via time-nuts
<time-nuts at febo.com> wrote:
>
> Ah, I had wondered about that but was probably being a bit selfish as I
> only have the GPS based units:-)
>
> Given the similarity, I would assume where we've got to on these
wouldn't
> be a bad starting point, and at least identifying the 1PPS input on the
> interface connector should be straightforward enough.
>
> Regards
>
> Nigel GM8PZR
>
>
>
> In a message dated 02/11/2014 19:41:07 GMT Standard Time, kb8tq at n1k.org
> writes:
>
> Hi
>
> No, once we get the GPS end worked out, we need to do the same thing
for
> the non-GPS end. If we can fake it into working with just a PPS, it’s
the
> perfect thing to use to attach an OCXO to a newer GPS (like the Jackson
Labs
> part …).
>
> Bob
>
>> On Nov 2, 2014, at 2:15 PM, GandalfG8--- via time-nuts
> <time-nuts at febo.com> wrote:
>>
>> Hi Gotz
>>
>> That's great stuff, thank you, I'll try that later.
>>
>> At this rate we'll soon be finding ways of doing this without any
> wiring
>> whatsoever, perhaps we could start with just standing it upside down
in
> a
>> dark corner on the night of the full moon:-)
>>
>> Regards
>>
>> Nigel
>> GM8PZR
>>
>>
>> In a message dated 02/11/2014 17:58:12 GMT Standard Time,
> goetz at g-romahn.de
>> writes:
>>
>>
>>
>> Am 02.11.2014 15:08, :
>>> Ooh err, whoops, and oh dear !!
>>>
>>> Arthur, I've only just had a chance to look at your latest photos,
and
>>> unless I've really got my wires crossed, if you'll pardon the
>> expression:-),
>>> your links on J5 are not shown on pins 2, 10, 12, and 15, but on
> pins
>> 4, 6,
>>> 11, and 13.
>>>
>>> As far as I'm aware the numbering from the front of that connector
as
>
>> shown
>>> starts in the top right hand corner and every row is numbered right
to
>>> left.
>>> That's certainly how mine are numbered anyway, and I wired them
>>> accordingly, and it worked, so where the heck does that leave us
> now?:-)
>>>
>> --------------------------
>> thanks Nigel for detecting this glitch. I removed all jumpers now and
>> tested some reasonable new/old combinations resulting in very simple
>> scheme:
>> it seems to be sufficient to connect pin2 and pin3 to pin8 (ground).
>> Numbering as provided by Nigel and markings on my 15 pin-plug.
>>
>> Götz
>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
More information about the Time-nuts_lists.febo.com
mailing list