[time-nuts] 3048A software question

[Adrian]

David,

the 82335 drivers came with the complete SW package that I sent you.
I don't know if the drivers and SW are running with any more recent or
non MS versions than MS-DOS 6.0.
But, it's as easy to find out as it gets. Back in the day the whole OS
fitted on a floppy disk and 640k of memory, together with a 33 MHz 486
did the job.

Btw. a modern 2,000 MHz or something clocked PC with 4,000,000k of
memory doesn't seem to work any faster...
And, no, even if you get MS-DOS installed on it, you're not gonna have
much fun.

Adrian


davidh schrieb:
>
>
> Folks,
>
> I'm also working on getting the MSDOS version running. What is the
> most recent version of DOS that people have found to work with the A
> 01.01 version.
>
> Also, can anyone advise where the command drivers for the 82335 can be
> found?
>
> Cheers,
>
> david
>
>> Hi Adrian,
>>
>> Got the spec lines working now, thanks!
>>
>> Yes, the DOS version. I was hoping for an updated user manual for
>> that version as the manual describes the other software version, and
>> maybe a slightly later sw version. Oh well.
>>
>> Thanks for you help!
>> Said
>>
>>
>>
>> On Feb 17, 2012, at 5:06, Adrian
>> <rfnuts-KvP5wT2u2U0 at public.gmane.org> wrote:
>>
>>> Said,
>>>
>>> are you using the Opt. 311 (MS-DOS) software?
>>> I don't know of any more recent versions.
>>>
>>> To answer your initial question:
>>> You can not change anything on the diagram _after_ the measurement,
>>> not even the title.
>>> The spec lines will be visible only when you have defined them prior
>>> to starting the measurement.
>>>
>>> Regards,
>>> Adrian
>>>
>>>
>>> SAIDJACK-YDxpq3io04c at public.gmane.org schrieb:
>>>> Hello team,
>>>>
>>>> I am trying to get an HP 3048A system up and running, and I am having
>>>> problems with enabling spec limit lines on the graph.
>>>>
>>>> I can enter the spec line data under the "manipulate results" then
>>>> "spec
>>>> lines" menu, but the lines I entered are not visible. There are the
>>>> standard
>>>> spec lines visible when I do the internal noise floor test, so I
>>>> know this
>>>> should work.
>>>>
>>>> Does anyone know how to enable these properly? The user manual
>>>> doesn't talk
>>>>   about this, and it is written for an older version of the software
>>>> anyway's.
>>>>
>>>> Also, I have software version A 01.01 from 1994, does anyone have
>>>> any more
>>>> recent software version?
>>>>
>>>> Thanks in advance,
>>>> Said
>>>> _______________________________________________
>>>> time-nuts mailing list -- time-nuts-JSkTLETqlTM at public.gmane.org
>>>> To unsubscribe, go to
>>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>>> and follow the instructions there.
>>>>
>>>
>>>
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts-JSkTLETqlTM at public.gmane.org
>>> To unsubscribe, go to
>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>