[time-nuts] How did they distribute time in the old days?

billriches bill.riches at verizon.net
Wed Oct 14 21:59:56 UTC 2015


I have been using 2 D cells in series to wind my clock - Every Labor Day I change the batteries!  Has anyone used Ken's for a rebuild.  Mine is still chugging along - amazing as some of the bushings are ovals and the gears can really move around in them!!

73,

Bill

-----Original Message-----
From: time-nuts [mailto:time-nuts-bounces at febo.com] On Behalf Of Brooke Clarke
Sent: Wednesday, October 14, 2015 2:02 PM
To: Nick Sayer; Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] How did they distribute time in the old days?

Hi Nick:

One of my Self Winding Clock Co. (WU) clocks was taken down yesterday for painting.
When put up one of the Ken's Clock Synchronizers was installed and the hands moved to align with the heart shaped cam it uses, but it never worked.
The problem was it used a 4.5 Volt signal which can develop the current needed to pull the sync electromagnet the time constant is far too slow.
I'm going to add a high voltage circuit with series resistor to get the time constant down one or two orders of magnitude.  The key to this is a PCB I make that holds 5 each 9V batteries connected in series, so I'll use one, two or more of them to get the time constant down.
http://www.prc68.com/P/45VS.html

Before I had the 45 Volt Stick I was considering getting the needed high voltage by charging a cap a minute or two before the top of the hour and discharging it through a resistor.  Here's a video showing that would work.
http://www.prc68.com/I/SWCC.shtml#Experiments_Feb_2014_

Mail_Attachment --
Have Fun,

Brooke Clarke
http://www.PRC68.com
http://www.end2partygovernment.com/2012Issues.html
http://www.prc68.com/I/DietNutrition.html
Nick Sayer via time-nuts wrote:
>> On Oct 14, 2015, at 4:42 AM, billriches <bill.riches at verizon.net> wrote:
>>
>> Not milisecond time distribution but time related!
>>
>> In the early half of the 1900s Western Union was in the time 
>> business.  They would rent businesses such as banks, office 
>> buildings, etc  clocks for a few dollars a month.  These were 
>> pendulum wall clocks that had 2 #6 dry cell batteries inside that 
>> would wind them every hour or so. The clocks were connected to the WU 
>> telegraph line and for a minute before and after  the top of the hour 
>> all traffic on the circuit would stop.  Exactly at the top of the 
>> hour they would push a pulse of 50 ? volts or so over the line and it would reset the clock to the top of the hour.
> The WU standard time service goes back further than the turn of the 20th century. It started in 1870.
>
> I’ve always wanted to get my hands on one of those clocks and come up with a circuit to recreate the synchronization signal for it, probably with a Raspberry Pi running ntpd and a big ol’ MOSFET. The problem is that at this point, those clocks are quite expensive once they’re reconditioned.
>
> My understanding (perhaps incorrect) was that the sync pulse was once daily and, as you said, would cause the hands to “snap” to 12. The trailing edge of the pulse was synchronized and would release the clock to operate normally.
>
> That they had something as accurate and widespread as it was so early is astonishing.
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to 
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>

_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.


---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus




More information about the Time-nuts_lists.febo.com mailing list