[time-nuts] Inside a CTS 1960017 OCXO
Rob Sherwood.
rob at nc0b.com
Sun Feb 28 00:20:18 UTC 2016
Both Adam and I measure the same spurs. Rob, NC0B
-----Original Message-----
From: time-nuts [mailto:time-nuts-bounces at febo.com] On Behalf Of Graham / KE9H
Sent: Saturday, February 27, 2016 2:08 PM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] Inside a CTS 1960017 OCXO
Rob:
Are you sure you were running it with a clean power supply?
Any 60 Hz ripple on the supply could show up as AM/PM modulation.
You might want to try another 5V power supply before you give up on the oscillator.
--- Graham
On Sat, Feb 27, 2016 at 11:35 AM, Rob Sherwood. <rob at nc0b.com> wrote:
> Hi Dan,
>
> I purchased two of these, and VA7OJ one. One of mine is defective,
> and the seller is going to replace it. What was disappointing was all
> the spurious at 60 Hz intervals relatively close-in to the 10 MHz
> carrier. I suppose if all one wants is a reasonably accurate 10 MHz,
> then they work OK. My good one and Adam's unit were 1x10^7 low in
> frequency once warmed up, and there are pins for frequency adjustment
> and sync to another standard. However if one wanted it for an
> oscillator with good close-in phase noise, the spurs ruin that hope.
>
> Do you know if there is a chopper at 60 Hz that runs the proportional
> oven that is the source of all the spurious?
>
> Rob
> NC0B
>
> -----Original Message-----
> From: time-nuts [mailto:time-nuts-bounces at febo.com] On Behalf Of
> Daniel Watson
> Sent: Saturday, February 27, 2016 9:48 AM
> To: time-nuts at febo.com
> Subject: [time-nuts] Inside a CTS 1960017 OCXO
>
>
>
> Hi,
>
> I'm sure many of you are tracking the cheap CTS 10MHz OCXOs available
> on eBay right now. I purchased a case of them, and decided to crack one open.
> I took pictures along the way, thinking that might be interesting to
> the list. Here is the blog post if you are interested:
>
>
> http://syncchannel.blogspot.com/2016/02/10mhz-ocxo-teardown-cts-196001
> 7.html
>
> Comments on the internal construction of the OCXO are welcome. It
> seems pretty straightforward inside though.
>
>
> Best regards,
>
> Dan W.
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
>
>
> --
> If this email is spam, report it to
>
> https://support.onlymyemail.com/view/report_spam/ODExMjI6MTg1NzM0MDA3N
> Tpyb2JAbmMwYi5jb206ZGVsaXZlcmVk
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
--
If this email is spam, report it to
https://support.onlymyemail.com/view/report_spam/ODExMjI6MTg1NzM4NTM3Nzpyb2JAbmMwYi5jb206ZGVsaXZlcmVk
More information about the Time-nuts_lists.febo.com
mailing list