[time-nuts] Transformer inrush current and transformer simulation

Chris Albertson albertson.chris at gmail.com
Sat Jun 4 06:06:48 UTC 2016


Don't let the start of the simulation be the power on time.  Best to
set up the AC mains volts at zero volts for a half second then go up
to 120 VAC.  So you actually simulate the power switch.  The time
before the start of the run is not defined

Also you should Google "spice transformer model" and see how others
have done it.  You will need to add some extra inductors and series
resistance.  As you found the Spice model does not have magnetics in
it.  It is simply a pair of coupled inductors.

On Fri, Jun 3, 2016 at 10:40 AM, Attila Kinali <attila at kinali.ch> wrote:
> On Fri, 03 Jun 2016 12:37:26 -0400
> "Mike Monett" <timenuts at binsamp.e4ward.com> wrote:
>
>> I found a significant error in the LTspice analysis. I was wondering how
>> the current could jump instantaneously at zero when the voltage is applied
>> at the peak. That violates magnetism.
>>
>> It turns out it doesn't. When LTspice starts an analysis, it first
>> calculates the operating point. For the Sine voltage source at 90
>> degrees, it applies the full voltage across the load. In this case,
>> it was 169.7V across 1 ohm, resulting in 169.7 Amps. That is what
>> was plotted, and is a significant error.
>
> Actually, spice (the engine behind LTspice) does a DC analysis before
> almost all modes of operation. This DC analysis has the intention to
> start the circuit from a steady-state point and thus to reduce simulation
> time. In order for this to work properly, you have to specify the DC voltage
> and currents for all sources correctly. Spice messes this up at times
> making the first part of a transient simulation worthless (it has even
> worse problems when you do an AC analysis). Additionally LTspice hides
> too much of these small complications for the problems to be visible to
> the untrained eye and also at times makes it harder to provide the correct
> values. Thus, caution is advised.
>
> The general rule of "Never trust a simulation you haven't
> forged yourself" applies.
>
>
>> Out of 13 examples I analyzed, I found only one that involves unloaded
>> transformers.
>>
>> I found many references that discuss transformer inrush current caused by
>> core saturation. This is a serious problem as it puts stress on the
>> components and reduces operating life.
>
> I only had a quick glance at your webpage, but it seems that you used
> the standard LTspice transformer model. Unfortunately, this is not a
> good model to study this kind of behaviour. For one, the only loss considered
> in the model is the winding coupling, it doesn't even directly consider
> resistive losses in the windings. In this case, the two most important effects
> that you need to include are saturation and core losses, which are both
> frequency dependent. The cores of electric machine transformers are very
> poor when it comes to their "high" frequency behaviour. Where high frequency
> starts somewhere closely above mains frequency. Ie 1kHz is already so far off
> that somewhere around 90% of the energy would be dissipated in the core.
> The sharp rise in voltage and the leading inrush current have frequency
> components that are way higher than mains frequency. Hence the linear model
> you used will give inaccurate results, to put it mildly.
>
>
> Unfortunately, building an accurate transformer model in spice is not
> easy and depends on higher order functions that might or might not be
> available in the flavour you use. Not to mention that you will need
> to have good (measured) numbers on the non-ideal behaviour of a transformer,
> which are also not easy to get by.
>
>
>                                 Attila Kinali
>
> --
> It is upon moral qualities that a society is ultimately founded. All
> the prosperity and technological sophistication in the world is of no
> use without that foundation.
>                  -- Miss Matheson, The Diamond Age, Neil Stephenson
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.



-- 

Chris Albertson
Redondo Beach, California



More information about the Time-nuts_lists.febo.com mailing list