[time-nuts] Vintage Frequency Measurement

[Bob Stewart]

In fact, I used a similar method for adjusting the AOR DDS-2A synthesizer on my Collins rig.  I tune an AM radio to WWV.  And I tun the DDS-2A / Collins to the same signal only using SSB.  Then when WWV is sending the tone modulated signal, I tune the DDS-2A calibration control to eliminate the beat note between the two tones.  Then flip to the other sideband and repeat.  It's much better than trying to null two carriers.  Even better if you use stereo headphones with the left on one radio and the right on the other.

Bob




      From: "jmfranke at cox.net" <jmfranke at cox.net>
 To: Discussion of precise time and frequency measurement <time-nuts at febo.com>; Bob Albert <bob91343 at yahoo.com> 
 Sent: Sunday, February 12, 2017 2:49 PM
 Subject: Re: [time-nuts] Vintage Frequency Measurement
   
A more accurate way to adjust for zero beat is to tone modulate one of the signals. The waxing and waning of the tone is easier to discern than for the background noise. 

"Accurate Zero Beating, another perspective.
When trimming an oscillator so it or one of its harmonics zero beats with WWV or other standard frequency transmission, much comment has been made over the ability to approach true zero beat.  When the harmonic is directly zero beat, the stated accuracy is generally in the 1-5Hz range.  There is a technique that allows one to repeatedly zero beat to a much higher accuracy.  The method is called the “Three-Oscillator Method” and dates back to the 1930’s, or earlier.  The earliest discussion I have found was on page 47 of Bulletin 10, “Frequency Measurements at Radio Frequencies,” published by the General Radio Company in February 1933.  The bulletin states that the “method has been in use for a number of years…”  The technique is also presented in sections II and XII of the 1956 Technical Manual (TM11-2665) for the AN/URM-18 Frequency Calibrator Set, the military version of the General Radio Type 1100-A Frequency Standard.  More recently, Alan Melia, G3NYK, reports an 
 accuracy of 0.1 Hertz using the same technique, http://www.alan.melia.btinternet.co.uk/freqmeas.htm .
The three oscillators are the standard, the unknown, and either another lesser accuracy oscillator or a receiver BFO.  The AN/URM-18 and the General Radio 1100-A frequency standards utilize regenerative receivers.  Using reception of WWV as an example; in normal practice the unknown or a harmonic of the unknown is adjusted to zero beat with WWV by injecting a sample of the unknown source into the antenna of an AM receiver tuned to one of the WWV transmissions.  As the unknown is trimmed or adjusted to match WWV, a beat frequency will be heard that approaches 0 Hz or zero beat with the WWV transmission.  Unfortunately, the audio bandpass of the receiver and the observer’s ear limit hearing a beat frequency much below ten Hz.  It is possible to reach closer beat frequencies by listening to the background noise wax and wane, but the results are not readily repeatable.  Now, a third source is introduced when the receiver BFO is turned on or the regenerative receiver is adjusted to osci
 llate.  With the unknown source temporarily disconnected, the receiver is tuned to give a nominal 1 kHz beat frequency while receiving the WWV transmission.  When the unknown source is once again added, the 1 kHz beat will wax and wane at a rate equal to the beat between the unknown source and the WWV transmission.  Changing the BFO or receiver tuning only changes the frequency of the tone that waxes and wanes.  The waxing and waning rate is determined solely by the beat between the WWV transmission and the unknown source.  It is now easy to reliably adjust the unknown, or its harmonic, to within a fraction of a Hertz of the WWV transmission.

John M. Franke  WA4WDL
4500 Ibis Ct.
Portsmouth, VA 23703
jmfranke at cox.net