[time-nuts] Am I doing something wrong?
Bill Beam
wbeam at gci.net
Wed Sep 25 20:55:23 UTC 2019
I am not sure, but I belive that DAC steering may be derived from GPS PPS
compared to osc derived PPS signal. There may be a component failure
blocking the PPS signal(s). Is there a pulse on the PPS output port?
There is no documentation of the hardware available....
On Wed, 25 Sep 2019 12:20:08 -0400, Roger Rehr W3SZ wrote:
>Thanks to Bill and Mike for the very helpful info!
>Unfortunately, doing warm reset, cold reset, factory reset, multiple
>self surveys did not solve the problem.
>Forcing Disciplining to Enabled did not help.
>Tuning the oscillator did not help.
>I can manually control the DAC voltage using appropriate commands and
>the 10 MHz output changes appropriately following each manual command.
>But the DAC voltage doesn't respond to GPS input.
>I note from my old records that when the unit is working properly and
>the DAC IS being controlled by the GPS, Lady Heather still says "Doing
>fixes", because fixes are in fact being done.- But when Lady Heather is
>working properly, she says that the Discipline mode is "Normal" instead
>of "Power-Up" as she does now.
>I used TBoltMon.exe to see if I could get any more info on the problem.-
>In TBoltMon.exe's GUI under "Disciplining Status" Mode is listed as "(1)
>Power-up" and Activity is listed as "(1) Osc Warm-up".
>So I wondered if the problem is that the Thunderbolt thinks that the
>oscillator has not warmed up and therefore won't come out of Power-Up
>mode.- But the manual says that the Tunderbolt won't start acquiring
>satellites and do the self survey until it has warmed up.- And the
>situation is that it has acquired satellites and it has done the self
>survey, both of which would suggest that it thinks that the oscillator
>HAS warmed up.- The the TBoltMon reading on the oscillator status seems
>to be inconsistent with how the Thunderbolt is performing;- it is acting
>like the oscillator IS warmed up, at least in some respects.
>Are there any schematics or diagrams or service manuals available for
>the Thunderbolt?- I couldn't find any with Google.
>Thanks again to Bill and Mike and all for your help!
>73,
>Roger
>W3SZ
>On 9/24/2019 1:32 PM, Roger Rehr W3SZ wrote:
>> HI All,
>>
>> I am wondering if I have set up my Trimble Thunderbolt wrong.
>>
>> I have corrected for roll-over and everything looks good in Lady
>> Heather but the Thunderbolt stays in Power-up mode according to Lady
>> Heather, and is always "doing fixes" even though I have entered the
>> lat and lon for a fixed location.
>>
>> According to Lady Heather Disciplining is OK, and of course the log
>> reflects this as well
>>
>> #! new minor alarm state 0800:- Tracking sats- - Discipline OK- - : at
>> tow 235167
>>
>> You can see the situation from this screen grab of Lady Heather:
>> http://w3sz.com/TrimbleLadyHeather.PNG
>>
>> Have I done something wrong in configuration, or is this consistent
>> Power-up mode and "doing fixes" notation the expected behavior?
>>
>> I am using the Thunderbolt as at 10 MHz source for my microwave station.
>>
>> Thanks in advance and 73,
>>
>> Roger Rehr
>> W3SZ
>_______________________________________________
>time-nuts mailing list -- time-nuts at lists.febo.com
>To unsubscribe, go to http://lists.febo.com/mailman/listinfo/time-nuts_lists.febo.com
>and follow the instructions there.
Bill Beam
NL7F
More information about the Time-nuts_lists.febo.com
mailing list