[time-nuts] Re: HP 5071A operating parameter trends
John Ackermann N8UR
jra at febo.com
Sat May 13 15:54:43 UTC 2023
I usually keep mine in standby but happen to have powered it up about a
week ago. When it's running I log all the params each minute into an
InfluxDB database. Here's a screenshot of the Emult voltage which
stabilized at about 1912.
That's higher than either you or Tom reported. I don't know whether the
absolute value is important, or the change in value over time.
Per Bob's note, I just looked at the beam current and it's been flat at
100 nA forever.
John
On 5/13/23 10:42, Stan via time-nuts wrote:
> I have been running my "new" 5071A for the past couple of days. I've been
> watching the output of the status message and captured a few of them below.
> The first capture was immediately after the 5071A locked after coming out of
> standby.
>
>
>
> Has anyone else been doing this? Are there particular trends I should be
> aware of that might indicate the beginnings a problem? So far, my 5071A is
> operating perfectly, with no errors on the log file.
>
>
>
> Thanks,
>
> Stan
>
>
>
> MJD 131 23:56:19
>
> CBT ID: 3839A00612(S)
>
> Status summary: Operating normally
>
> Power source: AC
>
> Log status: 6 entries
>
>
>
> Freq Offset: 0e-15 Osc. control: -3.43 %
>
> RF amplitude 1: 22.7 % RF amplitude 2: 22.6 %
>
> Zeeman Freq: 39949 Hz C-field curr: 12.218 mA
>
> E-multiplier: 1565 V Signal Gain: 14.4 %
>
>
>
> CBT Oven: 8.9 V CBT Oven Err: 0.45 C
>
> Osc. Oven: -8.8 V Ion Pump: 0.6 uA
>
> HW Ionizer: 1.0 V Mass spec: 10.5 V
>
> SAW Tuning: 0.0 V DRO Tuning: 5.6 V
>
> 87MHz PLL: 1.2 V uP Clock PLL: 2.6 V
>
> +12V supply: 12.3 V -12V supply: -12.1 V
>
> 5V supply: 5.3 V Thermometer: 42.2 C
>
>
>
> ____________________________________________________
>
>
>
> MJD 133 03:59:20
>
> CBT ID: 3839A00612(S)
>
> Status summary: Operating normally
>
> Power source: AC
>
> Log status: 6 entries
>
>
>
> Freq Offset: 0e-15 Osc. control: -4.05 %
>
> RF amplitude 1: 22.8 % RF amplitude 2: 22.2 %
>
> Zeeman Freq: 39949 Hz C-field curr: 12.218 mA
>
> E-multiplier: 1569 V Signal Gain: 14.4 %
>
>
>
> CBT Oven: 6.6 V CBT Oven Err: -0.02 C
>
> Osc. Oven: -8.9 V Ion Pump: 0.2 uA
>
> HW Ionizer: 1.0 V Mass spec: 10.4 V
>
> SAW Tuning: 0.0 V DRO Tuning: 5.6 V
>
> 87MHz PLL: 1.2 V uP Clock PLL: 2.5 V
>
> +12V supply: 12.3 V -12V supply: -12.2 V
>
> +5V supply: 5.3 V Thermometer: 43.4 C
>
>
>
> ____________________________________________________
>
>
>
> MJD 133 13:09:58
>
> CBT ID: 3839A00612(S)
>
> Status summary: Operating normally
>
> Power source: AC
>
> Log status: 6 entries
>
>
>
> Freq Offset: 0e-15 Osc. control: -4.19 %
>
> RF amplitude 1: 22.9 % RF amplitude 2: 22.2 %
>
> Zeeman Freq: 39949 Hz C-field curr: 12.218 mA
>
> E-multiplier: 1562 V Signal Gain: 14.4 %
>
>
>
> CBT Oven: 6.5 V CBT Oven Err: -0.02 C
>
> Osc. Oven: -8.9 V Ion Pump: 0.2 uA
>
> HW Ionizer: 1.0 V Mass spec: 10.4 V
>
> SAW Tuning: 0.0 V DRO Tuning: 5.6 V
>
> 87MHz PLL: 1.2 V uP Clock PLL: 2.5 V
>
> +12V supply: 12.3 V -12V supply: -12.2 V
>
> +5V supply: 5.3 V Thermometer: 42.8 C
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at lists.febo.com
> To unsubscribe send an email to time-nuts-leave at lists.febo.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: hp5071a_emult.png
Type: image/png
Size: 152713 bytes
Desc: not available
URL: <http://febo.com/pipermail/time-nuts_lists.febo.com/attachments/20230513/ca1e5ca3/attachment.png>
More information about the Time-nuts_lists.febo.com
mailing list