[time-nuts] Re: Oscilloquartz 8663-XS stability problem

[Brian K]

I found an old time-nuts thread that discusses whether or not the 866S-XS uses a Double Oven.

https://febo.com/pipermail/time-nuts_lists.febo.com/2020-February/099099.html

I don't know it this question was definitively answered.

I have seen AliExpress ads that include photos of a similar device where the label specifically mentions 'Double Oven'.
The part number is not quite the same - '108663-01' made by 'UCT'.

[cid:cafb73c8-a8a2-451d-a9a9-687dabff4a70]

The eevblog link below has photos of what is inside the UCT device:-

https://www.eevblog.com/forum/testgear/inside-the-uct-108663-1-10-mhz-double-oven-ocxo/msg4909163/#msg4909163
Inside the UCT 108663-1 10 MHz Double Oven OCXO - Page 1<https://www.eevblog.com/forum/testgear/inside-the-uct-108663-1-10-mhz-double-oven-ocxo/msg4909163/#msg4909163>
Inside the UCT 108663-1 10 MHz Double Oven OCXO - Page 1
www.eevblog.com

The device I have does not mention 'Double Oven' on the label.
The part number is simply '8663-XS' similar to that below:-

[cid:f4157cbe-4e4f-407c-af27-79eb000b771c]

The actual label on my device gives:-
Art. 945.866.302.02
Serial No. 08/03 MY 38701

________________________________
From: Brian K via time-nuts <time-nuts at lists.febo.com>
Sent: 27 October 2023 15:15
To: time-nuts at lists.febo.com <time-nuts at lists.febo.com>
Cc: Brian K <brian_mk at hotmail.co.uk>
Subject: [time-nuts] Oscilloquartz 8663-XS stability problem

I recently constructed a homebrew 10MHz distribution amp.
It has provision for both an external 10MHz source such as a GPSDO or an internal OCXO.
For the internal OCXO I chose a used Oscilloquartz 8663-XS from China.

When I began testing the unit I discovered an issue with frequency / temperature stability.

I plotted a graph that shows the external temperature of the OCXO can as the device warms up.
It stabilises at 60degC after around 45 minutes.

I also plotted the frequency error measured using a Racal 1998 with an external 10MHz clock from a GPSDO.
The frequency also appears to stabilise after around 45 minutes.

[cid:0acb1b9d-a986-47a3-85de-53b95bb8479e]

So far so good.

However I find that if I leave the unit running for a few hours, the frequency gradually drifts upwards by up to 0.5Hz.
That is well outside the 8663-XS specification. It is supposed to remain within 4x10^-9 from -20 to +70degC (I assume that is external ambient temp).
The OCXO temperature (as measured on the outer can) remains constant at 60 degC.
The tuning voltage and the supply voltage (12V) also remain constant.
The tuning voltage comes from a LH0070 10V precision reference and a 10 turn 10K trimmer.
I expected the tuning voltage required for 10MHz to be around 5V. The spec indicates a range of 0->10V.
I found that the tuning voltage needed to be set to just below 10V to get 10MHz.
Initially I thought that perhaps that's because it's an old used device.
Subsequent tests however make me think it's related to temperature.

I find that if I remove the equipment case lid, the frequency drifts slowly downwards.
When I replace the lid, the frequency error slowly recovers.
I assume the OCXO temperature drops slightly when the lid is removed despite it having ventilation slots directly above the OCXO.
I expected the OCXO internal temperature to be maintained to within around +/- 1degC by the heater control circuit such that it would compensate for small external temperature variations.

I am at a loss to explain what is going on and am running out of ideas.
It appears that the OCXO internal temperature regulation is not working as well as it should.
Is it just my particular device that behaves in this way or is it a common issue with this OCXO?

I don't want to buy another used device from China (around 40 GBP) only to find the same problem.

I would welcome any thoughts/suggestions from the experts here at time-nuts.

For the full story, please refer to my recent thread in the eevblog forum:-
https://www.eevblog.com/forum/projects/oscilloquartz-8663-xs-ocxo/


[cid:18711b70-068e-474b-8ab5-74e886152aa1]

Regards,

Brian.

-------------- next part --------------
A non-text attachment was scrubbed...
Name: image.png
Type: image/png
Size: 254042 bytes
Desc: not available
URL: <http://febo.com/pipermail/time-nuts_lists.febo.com/attachments/20231028/8d3431b6/attachment.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image.png
Type: image/png
Size: 659760 bytes
Desc: not available
URL: <http://febo.com/pipermail/time-nuts_lists.febo.com/attachments/20231028/8d3431b6/attachment-0001.png>