[time-nuts] HP Z3805A com port and monitoring questions

Azelio Boriani azelio.boriani at screen.it
Mon Oct 15 10:12:23 EDT 2012


you can also preset the receiver to the factory settings:

:SYST:PRESET

for the SCPI command reference you can see the manual:

www.leapsecond.com/museum/*hp58503a*/097-58503-13-iss-1.pdf



On Mon, Oct 15, 2012 at 2:45 PM, Said Jackson <saidjack at aol.com> wrote:

> Edgardo,
>
> Pretty sure it was 9600 8N1 no flow control.
>
> Came right up in GPSCon..
>
> Maybe its your cable, I used the cable that was shipped to me with the
> unit.
>
> I did have to manually initiate the auto survey, so comms are important..
>
> Bye
> Said
>
> Sent From iPhone
>
> On Oct 14, 2012, at 21:36, Edgardo Molina <xe1xus at amsat.org> wrote:
>
> > Dear Said,
> >
> > I am having a very hard time trying to guess the communication port
> configuration of the HP Z3805A. I am trying with different port settings to
> match the PC and using different monitor and control programs. The
> afternoon was not that fruitful regarding this. Is there a chance you have
> the default port configuration for the Z3805A so I can match my PC serial
> port configuration?
> >
> > I might be unavailable to respond to you tomorrow during the day, as I
> will be at Queretaro with restricted access to the Internet. Despite this I
> will be able to read my mail, not respond to it. Hope you don't mind.
> >
> > Your kind help is always welcome. Thanks.
> >
> > Regards,
> >
> >
> >
> > Edgardo Molina
> > Dirección IPTEL
> >
> > www.iptel.net.mx
> >
> > T : 55 55 55202444
> > M : 04455 20501854
> >
> > Piensa en Bits SA de CV
> >
> >
> >
> > Información anexa:
> >
> >
> >
> >
> > CONFIDENCIALIDAD DE INFORMACION
> >
> > Este mensaje tiene carácter confidencial. Si usted no es el destinarario
> de este mensaje, le suplicamos se lo notifique al remitente mediante un
> correo electrónico y que borre el presente mensaje y sus anexos de su
> computadora sin retener una copia de los mismos. Queda estrictamente
> prohibido copiar este mensaje o hacer usode el para cualquier propósito o
> divulgar su en forma parcial o total su contenido. Gracias.
> >
> >
> > NON-DISCLOSURE OF INFORMATION
> >
> > This email is strictly confidential and may also be privileged. If you
> are not the intended recipient please immediately advise the sender by
> replying to this e-mail and then deleting the message and its attachments
> from your computer without keeping a copy. It is strictly forbidden to copy
> it or use it for any purpose or disclose its contents to any third party.
> Thank you.
> >
> >
> >
> >
> >
> > On Oct 14, 2012, at 11:05 PM, SAIDJACK at aol.com wrote:
> >
> >> Hi Edgardo,
> >>
> >> I think the Z3805A and 58503A are identical, except in the rubber
> bumpers,
> >> maybe the power supply voltage setting, and the ID string..
> >>
> >> I don't really care, the three units I have perform much better than
> >> anything else I have, so that satisfies my requirements..
> >>
> >> In fact one of the units' ADEV can only be qualified by the BVA 8600  o
> >> scillator I have, and I don't know if I am measuring the BVA
> performance or the
> >> 58503A because I am measuring right at the specification of the BVA
> unit..
> >> Wish  I had two BVA's :)
> >>
> >> bye,
> >> Said
> >>
> >>
> >> In a message dated 10/14/2012 15:41:25 Pacific Daylight Time,
> >> xe1xus at amsat.org writes:
> >>
> >> Derived  question: Will I get better GPSDO performance if I use a 58503A
> >> receiver? Or  do you think our units match those 58503A GPSDOs out
> there?
> >>
> >> Again,  thanks to everybody who helped me to figure out about my
> receivers
> >> and their  inner workings. As always, you all made my day.
> >>
> >>
> >> Best  regards,
> >>
> >>
> >>
> >> Edgardo Molina
> >> Dirección  IPTEL
> >>
> >> _______________________________________________
> >> time-nuts mailing list -- time-nuts at febo.com
> >> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> >> and follow the instructions there.
> >
> > _______________________________________________
> > time-nuts mailing list -- time-nuts at febo.com
> > To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > and follow the instructions there.
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.



More information about the time-nuts mailing list